Maintenance Calorie Calculator Find Your Daily Calories See the...
Precise peptide dosing is essential in research settings, performance physiology, and longevity-focused protocols. Because peptides are typically supplied in lyophilized powder form and require reconstitution, dosage errors can occur if concentration calculations are not handled carefully.
This Peptide Dosage Calculator helps you calculate the exact volume to administer after reconstitution, based on total peptide content in the vial, added diluent volume, and your intended dose. It simplifies unit conversions and reduces calculation errors that may affect consistency and outcomes.
Calculate your exact syringe draw (in units and mL) from vial size, BAC water volume, and target dose
Enter the total amount of peptide in your vial (printed on the label) and the volume of bacteriostatic water (BAC water) you added during reconstitution. More water = lower concentration = larger draw volume per dose. The formula: Concentration (mcg/mL) = Peptide (mg) × 1000 ÷ BAC water (mL).
Common vial sizes: 2 mg, 5 mg, 10 mg, 15 mg, 20 mg. Check your vial label.
Most protocols use 1–3 mL. Use more water for low doses that require precise small draws. BAC water contains 0.9% benzyl alcohol and supports multi-dose vials for up to 28 days refrigerated (USP Chapter <797>, 2019).
Enter the dose you need per injection. Most research peptide protocols express doses in micrograms (mcg). Conversion: 1 mg = 1,000 mcg. If your protocol gives a per-kg dose (e.g. BPC-157 at 1–10 mcg/kg), multiply by your body weight first.
1 mg = 1,000 mcg. Typical research doses: 100–500 mcg (GHRPs), 250–500 mcg (BPC-157), 500 mcg–2 mg (TB-500). Always verify with your specific research protocol.
All calculations assume standard U-100 insulin syringes: 100 units = 1 mL, therefore 1 unit = 0.01 mL. Choose the physical syringe you have on hand. For doses requiring fewer than 10 units, a 0.3 mL syringe is strongly recommended for its finer half-unit graduation marks (PeptideReconstitute.com, 2026; PeptideWiki, 2026).
Your results will appear here after calculation.
| Dose | Volume (mL) | Syringe units (U-100) |
|---|
Highlighted row = your selected dose. All values based on your reconstitution concentration.
Bar shows what 1 dose represents as a fraction of your total vial content.
Step 1 — Concentration: Peptide (mg) × 1,000 ÷ BAC water (mL) = Concentration (mcg/mL)
Step 2 — Draw volume: Desired dose (mcg) ÷ Concentration (mcg/mL) = Volume (mL)
Step 3 — Syringe units: Volume (mL) × 100 = Units on a U-100 syringe
On a standard U-100 insulin syringe, 100 units = 1 mL, so each unit = 0.01 mL. The terminology comes from insulin dosing convention and applies to all U-100 syringes regardless of what is inside them (PeptideReconstitute.com, 2026; Peptide Regeneresis, 2026).
Lyophilized (dry) powder: Store at 2–8°C (refrigerator) short-term, or at −20°C for long-term storage. Most peptide powders remain stable for months to years when kept away from heat, light, and moisture (Particle Peptides; PeptideWiki, 2026).
Reconstituted with BAC water: Refrigerate immediately at 2–8°C (36–46°F). Stable for approximately 28 days. Label your vial with the reconstitution date. Discard if the solution becomes cloudy, discoloured, or develops particulates (USP Chapter <797>, 2019; Manning et al., Pharmaceutical Research, 2010).
Reconstituted with sterile water (no preservative): Use within 24 hours. Do not store for multi-dose use.
Never use: Tap water, distilled water, or any non-pharmaceutical liquid. These lack correct pH and sterility and will degrade the peptide and introduce contamination risk.
All calculations on this tool assume U-100 insulin syringes (100 units = 1 mL). Never substitute a U-40 veterinary syringe: a U-40 syringe uses 40 units per mL, which would cause a 2.5× overdose if U-100 math is applied to it. Always confirm your syringe packaging explicitly states "U-100" (Social Life Magazine, 2025; PeptideWiki, 2026).
Dead space: Fixed-needle U-100 syringes have negligible dead space. Luer-lock syringes with detachable needles may trap up to 0.05 mL in the needle hub — account for this by drawing slightly past your target mark (calculator.goldsupplier.com, 2026).
Peptides are commonly supplied in milligrams (mg) and reconstituted with bacteriostatic or sterile water measured in milliliters (mL). Once mixed, the concentration becomes a ratio of milligrams per milliliter (mg/mL). Accurate dosing requires converting the desired dose—often expressed in micrograms (mcg)—into the corresponding volume to draw.
For example, if a 5 mg vial is reconstituted with 2 mL of solution, the final concentration equals 2.5 mg/mL. If the target dose is 250 mcg (0.25 mg), the required volume is calculated by dividing the dose by concentration. Without systematic calculation, confusion between mg, mcg, mL, and insulin syringe units can easily lead to dosing mistakes.
In longevity research and metabolic optimization contexts, dose precision matters because peptide effects are often nonlinear and receptor-mediated. Small variations may alter signaling pathways, pharmacokinetics, or physiological response. Using a structured Peptide Dosage Calculator improves clarity, reproducibility, and overall dosing accuracy.
Understanding your body fat percentage…
Managing carbohydrates is key for…
Wondering how tall you—or your…
Understanding this calculator can raise questions. Here you’ll find clear, evidence-based answers to help you interpret your results and understand the science behind it.
Peptide concentration refers to how much peptide is present per unit of liquid after reconstitution (e.g., mg/mL). Peptide dosage refers to the actual amount administered per injection (e.g., 200 mcg). The calculator helps translate concentration into a measurable dosage volume.
Peptides are biologically active at relatively small doses. Since one milligram equals 1,000 micrograms, expressing doses in mcg allows for more precise titration and finer adjustments.
Adding more diluent lowers the concentration per milliliter but does not change the total amount of peptide in the vial. It simply alters how much liquid must be drawn to achieve the same dose.
This calculator is provided for educational and research purposes. Any therapeutic use of peptides should be supervised by a licensed healthcare professional and comply with applicable regulations.
Accurate peptide dosing requires careful attention to unit conversions, concentration calculations, and administration volume. The Peptide Dosage Calculator provides a structured and reliable method for determining precise dosage after reconstitution.
By reducing mathematical error and improving consistency, this Peptide Dosage Calculator supports safer research practices, clearer interpretation of results, and a more rigorous approach to peptide-based protocols within longevity and preventive health contexts.
